Our Latest Articles

Locksmith aligning maglock armature plate

Pass Inspections With Maglock Installation for Irish Property Managers

September 29, 2026

Yes, you can install a maglock on many door types, but a compliant setup needs a maglock and armature plate, a correctly sized power supply with battery backup, a request-to-exit device and, on escape routes, fire alarm integration with a manual green box release. Before you drill anything, work through the checklist below to confirm your door and frame suit the job, or book a professional survey if the door sits on an escape route.


TL;DR:

  • A maglock installation requires a matching armature plate, a properly rated power supply with battery backup, and a request-to-exit device for reliable operation.
  • For escape route doors, fire alarm integration and a manual green box release are mandatory, with additional coordination needed for fire safety compliance.
  • Bracket selection and precise alignment are critical; incorrect fitting or mismatched brackets can significantly weaken the lock’s holding force or cause misalignment issues.
  • Continuous power supply sizing and wiring practices, including proper cable routing and labeling, are essential to prevent faults and ensure system reliability.
  • Hiring a professional installer is recommended for complex setups, fire alarm integration, or if the door sits on an escape route, to ensure compliance and safe operation.

Ecslocksmiths
ecslocksmiths.ie
Strengthen Your Property Security
Ecslocksmiths provides commercial security solutions in Dublin, including electronic and high-security lock upgrades for business properties.
Visit Ecslocksmiths

Table of Contents

What you need before you start: parts, tools and compliance questions

A maglock installation has more moving parts than the lock itself. Before ordering anything, confirm the door type, the escape status of the route and whether you have the tools to do the mechanical and electrical work properly.

You will typically need:

  • Maglock and armature plate, matched in holding force to the door’s weight, width and traffic level.
  • Mounting bracket suited to the door swing: Z-bracket for inswing doors, L-bracket for outswing, and specialist brackets for narrow stile aluminium or glass doors.
  • Power supply unit (PSU) rated for the lock’s voltage and current draw, plus a battery backup for continuity during mains outages.
  • Request-to-exit (REX) device, such as a push-to-exit button or motion sensor, and door position switches to report open or closed status to the access controller.
  • Fixings, conduit and cable appropriate to the frame material, plus a multimeter for testing voltage and continuity at every stage.

For tools, you will want a drill with masonry and metal bits sized to the manufacturer’s quick-install guide, spade bits for cable runs through timber frames, a torque driver for the tamper-resistant fixings most maglocks specify, and a stud finder or frame scanner if you are working on a hollow metal or timber door frame.

Before buying anything, check whether the door sits on an escape route. Irish guidance requires escape routes to remain unobstructed at all times, and a government consultation has proposed tighter rules for door fastenings on escape routes to keep them immediately available for use. If the door you are working on is part of an escape route, you will need fire alarm integration and a manual release. This usually means bringing in a fire alarm contractor and, in many cases, a building design professional.

Frame and door suitability matter as much as the lock’s rated force. Glass doors, narrow aluminium stiles and fire-rated timber doors each need a specific bracket kit rather than a generic drill-and-fix approach, and mismatching the bracket to the door is one of the most common causes of a weak or misaligned installation.

Pro Tip: Photograph the door, frame and existing hardware before you order parts. Bracket manufacturers often need those details to confirm the correct kit.

As a rule of thumb: if the door is a standard timber or hollow metal door not on an escape route, and you are comfortable with a drill, a multimeter and basic wiring, DIY installation is realistic. If the door sits on an escape route, involves glass or curtain walling, or needs fire alarm integration, hire a locksmith or access control installer with commissioning experience.

Step-by-step mechanical installation: mounting the maglock and armature

Mechanical installation is where most maglock problems start, usually from rushed measurements or the wrong bracket. Work through this sequence in order, and do not skip the alignment checks.

1. Measure and mark with the door closed. Close the door fully and mark the centreline of the frame header and the door leaf where the magnet and armature will sit. Working with the door closed avoids the common mistake of mounting the armature slightly out of true, which shows up later as a weak or uneven hold.

2. Choose the bracket for your door type. An inswing door usually needs a Z-bracket to offset the armature plate away from the frame; an outswing door often takes a simpler L-bracket. Narrow stile aluminium doors and glass doors need dedicated S-bracket or glass-clamp kits rather than a standard bracket, since there is no timber or metal substrate to drill into in the usual way; more details on aluminium door bracket options can be found on the Aluminium ajtók - A Te ablakod site.

3. Drill pilot holes for the maglock body. Using the hole spacing from the manufacturer’s quick-install guide, drill pilot holes into the frame header. Manufacturer documents such as the UA-Lock-Magnetic-270kg quick install guide specify exact hole sizes and spacing for the lock body and bracket, and following those dimensions is the difference between a lock that holds its rated force and one that does not.

4. Fix the maglock to the frame. Secure the lock body with the fixings supplied, tightened to a firm, even torque rather than as tight as the driver will go. Most maglocks use tamper-resistant screw heads on the exposed face; fit these last, once you have confirmed alignment, since they are harder to remove for adjustment.

5. Mount the armature plate on the door leaf. Position the armature so its face sits flush with the magnet when the door is closed. This is the step where a rubber washer matters most.

6. Fit the rubber washer and metal washer sandwich. Every maglock armature should sit on a rubber washer, with metal washers either side, between the plate and the door. This sandwich lets the armature rock and self-align with the magnet face when the door closes, rather than binding at one edge. Overtightening the armature fixings crushes this movement out and reduces the lock’s effective holding force, even if the lock itself is rated correctly.

7. Allow for rocking movement before final tightening. Close the door several times before fully tightening the armature screws, letting the plate settle against the magnet face on its own. Only then apply final torque, checking that the plate still has a small amount of give.

8. Fit tamper screws and cable covers. Once alignment is confirmed, fit any tamper-resistant fixings and cable covers, and route cable neatly into the frame or surface conduit.

Bracket-specific notes worth knowing before you start:

  • Z-brackets offset the armature away from the door face on inswing doors and need slightly deeper pilot holes to clear the offset arm.
  • L-brackets are simpler and sit flush on outswing doors, but check the door’s closing clearance before fitting since the bracket adds a few millimetres of depth.
  • S-brackets are used where the magnet mounts to the frame soffit rather than the header, common on doors with limited header depth.
  • Glass-door sets clamp rather than drill, using a toughened glass clamp plate, and need the glass thickness confirmed before ordering since clamp kits are not universal.

Before calling the mechanical work finished, run these checks:

  • Gap tolerance: with the door closed, the armature face should sit flush against the magnet with no visible gap; a gap of more than a millimetre or two will noticeably reduce holding force.
  • Rocking test: gently push the closed door leaf; the armature should show a small amount of give rather than sitting rigid.
  • Preliminary pull test: with power connected, try to pull the door open by hand at a normal pace to confirm the lock is holding before you move on to wiring and commissioning.
  • Swing clearance: open and close the door through its full arc to confirm the bracket does not foul the frame or door closer.

Following the manufacturer’s own quick install guide for hole sizes and bracket dimensions matters more here than general advice, since drilling patterns vary between models even within the same holding-force class.

Power, control wiring and the components that make the system work

The magnet itself is only one part of a working system. Most installation problems trace back to underspecified power supplies, poorly placed REX devices or wiring mistakes rather than the lock body.

Maglocks are commonly rated at 12 VDC or 24 VDC, and the lock must run continuously at that voltage to hold its rated force, since a maglock draws power the entire time the door is secured. This continuous draw is different from an electric strike, which only draws power briefly during release, and it means your power supply has to be sized for sustained load, not just a momentary spike.

When selecting a power supply and battery backup:

  • Size the PSU to the combined continuous draw of the maglock plus any REX devices, sensors and access controller hardware sharing the same supply.
  • Add a battery backup rated to keep the lock and controller running through a mains outage, sized to your building’s expected outage duration rather than a token few minutes.
  • Check voltage drop on long cable runs; undersized cable on a run to a distant frame can starve the lock of its rated voltage even with a correctly sized PSU.

Request-to-exit devices and door position switches need thought about placement, not just wiring. A REX push button should sit at a height and location that occupants naturally reach when leaving, and a motion-sensor REX needs its detection zone tested so it does not trigger from corridor traffic outside the door. Door position switches, usually magnetic reed contacts, should be fitted so they report an accurate open and closed state to the access controller, since a false “closed” signal will let the system re-lock a door that has not actually shut.

Integration with access controllers and alarm panels usually means wiring the maglock’s power-cut path through a relay controlled by the access panel, with the REX and door contact wired as separate monitored inputs. Where the door also needs fire alarm release, the alarm panel’s output typically feeds the same power-cut relay, cutting power to the lock independently of the access controller whenever the alarm activates.

A few wiring practices are worth following as standard:

  • Route low-voltage cabling away from mains cabling and lighting circuits to avoid interference with sensor signals.
  • Label every cable at both ends before final fixing; unlabelled cable is the single biggest time cost in later troubleshooting.
  • Avoid fitting suppression diodes across the maglock’s terminals. On many modern locks these diodes cause residual magnetism, leaving the lock feeling sticky or slow to release even once power is cut.

Pro Tip: Test the REX and door contact wiring with a multimeter before connecting the lock itself. It is far easier to trace a wiring fault with the magnet disconnected.

Fire alarm integration and escape-route compliance

Any maglock fitted on an escape route needs more than a REX button. Irish guidance treats a maglock on an escape route as a “Special Locking Arrangement,” which must release automatically on fire alarm activation and include a manual override.

A government consultation on fire safety and escape routes proposes that escape routes remain unobstructed and that certain fastenings be prohibited unless they allow immediate opening from inside. In practice, this means a maglock cannot be the only thing standing between an occupant and an open escape route unless it is wired to release the moment the fire alarm activates.

Official guidance on door fastenings for doors on escape routes lists maglocks as an acceptable option only when they are interfaced with the fire alarm system and fitted with a manual “green box” emergency release, and it specifies that this arrangement should be specified by a qualified building design professional rather than decided on site.

Before fitting a maglock on any escape route:

  • Confirm the door’s fire and escape status with the building’s fire safety documentation or a design professional before ordering hardware.
  • Wire the fire alarm output to cut power to the lock independently of the access control system, so an alarm trips the release even if the access panel fails.
  • Fit a green box manual release at a visible, reachable point beside the door, wired to cut power to the lock directly.
  • Get sign-off from a fire officer or building design professional once the installation is complete, and keep that sign-off with the building’s fire safety file.

Technical Guidance Document B on fire safety is the other reference point worth consulting when assessing door fastenings on escape routes, alongside the appendix guidance above. Local approval is not optional on these doors: a maglock that looks correctly wired but lacks the fire alarm interface and green box release will fail an inspection regardless of how well it is mounted.

Testing, commissioning and handover checks

A maglock is not finished once it is mounted and wired. Commissioning is the stage that catches faults before occupants do, and it should be documented, not just performed.

1. Verify electrical basics. Measure voltage at the lock terminals with a multimeter to confirm it matches the rated voltage, check continuity on every wired connection, and confirm the battery backup takes over cleanly when mains power is disconnected.

2. Test the REX device. Trigger the REX button or sensor and confirm the lock releases within its expected delay and re-locks correctly afterwards.

3. Simulate the fire alarm release. With a responsible fire safety officer or building manager present, trigger the fire alarm and confirm the maglock releases immediately and stays released until the alarm is reset.

4. Test the green box manual release. Operate the manual release and confirm it cuts power to the lock directly, independent of the access controller or alarm panel.

5. Confirm door position reporting. Open and close the door several times and check the access controller logs accurate open and closed states each time.

6. Run a mechanical endurance check. Open and close the door repeatedly under normal use conditions, checking that the armature stays aligned and the lock continues to hold at full force.

For handover, produce a short commissioning record covering the voltage and continuity readings, the fire alarm simulation result with the officer’s name and date, and the battery backup test outcome. Keep this with the building’s fire safety file alongside any sign-off from the design professional who approved the escape-route arrangement.

Six maglock commissioning checks and handover records

Pro Tip: Set a maintenance reminder for six to twelve months out to retest the battery backup and REX response time, since battery capacity and sensor sensitivity both drift over time.

Common problems and troubleshooting checklist

Most maglock faults after installation fall into a small number of categories, and most can be diagnosed with a multimeter before you call anyone out.

If a maglock does not release, start by confirming that power is actually being cut to the lock terminals when the REX or access controller is triggered. A maglock is fail-safe by design, meaning it should unlock the instant power is removed, so a lock that stays locked almost always points to a fault in the power-cut path rather than the magnet itself. Check the relay and controller output before assuming the lock has failed.

  • Won’t release: confirm power is genuinely being cut at the lock terminals, then check the relay and controller output rather than the magnet.
  • Low holding force: re-seat the armature plate, confirm the rubber and metal washer sandwich is intact, and check for a gap between armature and magnet face.
  • Sticky or slow release: test for residual magnetism, often caused by a suppression diode fitted across the lock terminals; removing the diode usually resolves it.
  • Intermittent faults: isolate wiring from mechanical causes by testing the lock on a bench supply; if it behaves normally off the door, suspect wiring or alignment rather than the lock itself.

Misalignment problems usually trace back to the same cause: the armature was tightened before it had a chance to self-align, or the wrong bracket was fitted for the door’s swing direction. Loosening the armature screws, letting the door close and settle a few times, then retightening evenly often restores full holding force without swapping any parts.

Sticky locks are worth testing properly rather than guessing. Disconnect power, wait a moment, then check whether the armature separates cleanly from the magnet by hand. If it resists separation, residual magnetism from a suppression diode or a damaged magnet coil is the likely cause.

Typical Irish call-out and installation pricing reflects how much labour time these diagnostics take on site, since tracing a wiring fault through a frame can take longer than the original installation.

If you have checked power, relays and the armature sandwich and the fault persists, or if the door sits on an escape route, stop and call a qualified installer or electrician rather than continuing to test. Faults on fire-alarm-integrated systems in particular should not be left partially diagnosed.

Typical costs and labour considerations, and how to choose an installer

Costs for maglock installation vary with door type, wiring complexity and whether fire alarm integration is needed. As a general reference point, standard lock installations in Ireland often run between €70 and €150, with more complex or high-security installations reaching €300 or more, and call-out or emergency rates adding to the total.

Maglock installations tend to sit above simple lock fitting because of the extra labour: running low-voltage cable, sizing and fitting a PSU and battery backup, and wiring REX and door contact devices all add time beyond mounting the lock itself. Where fire alarm integration is required, coordinating with a fire alarm contractor and arranging sign-off from a design professional adds further cost and scheduling complexity, since the electrical work and the compliance sign-off are usually separate visits.

Before hiring an installer, ask:

  • Are they insured for the electrical and mechanical work involved, and can they show evidence of it?
  • Will they provide a written commissioning record covering voltage, battery backup and fire alarm release tests?
  • Can they supply references or examples of similar installations, particularly on escape routes?
  • What warranty do they offer on parts and labour, and for how long?

If the door sits on an escape route, insist on a site survey and a written compliance statement before work begins, rather than a verbal quote. A survey lets the installer confirm the correct bracket, PSU sizing and fire alarm interface for your specific door and building before any drilling starts, which avoids costly rework later.

Practical notes from ECS Locksmiths

Every maglock job throws up something the drawings did not show. Concealed steel frames behind a timber skin, door reveals a few millimetres off standard, or a previous installer’s redundant cabling left in the frame are all common, and they usually only show up once drilling starts.

Scheduling matters more than most people expect. When a job needs fire alarm integration, the mechanical fitting and the alarm contractor’s release wiring rarely happen on the same visit, and lining up both trades with the building manager’s availability is often the slowest part of the job, not the drilling.

Small costs tend to appear around the edges: a non-standard bracket for a glass door, an extra length of conduit for a concealed cable run, or a battery backup upgrade once the full accessory load is added up. None of these are large on their own, but they are worth budgeting for rather than treating as surprises.

A professional locksmith service can install and commission maglock systems on residential and commercial doors, often offering 24/7 availability for callouts outside normal hours.

— Barry

ECS Locksmiths’ maglock installation and how to request a quote

If the escape-route rules, wiring and commissioning steps above feel like more than you want to take on yourself, that is exactly the job ECS Locksmiths handles day to day. A visit typically includes a site survey to confirm the right lock, bracket and power setup for your door, a written quote before any work starts, and a compliant installation finished with full commissioning and a handover record you can keep on file.

Ecslocksmiths

Booking starts with a free estimate, and ECS Locksmiths aims to respond quickly to both scheduled installation requests and urgent callouts. What you get on site is a locksmith working through the same mechanical and electrical checks covered above, mounting, wiring, testing and fire alarm coordination where needed, rather than a partial fit you have to finish yourself.

  • Free site survey and written quote before work begins.
  • Full mechanical and electrical installation, including PSU, battery backup and REX wiring.
  • Commissioning tests and a handover record, with fire alarm coordination arranged where the door needs it.

If you would rather have a professional handle the installation from survey to sign-off, request a quote from ECS Locksmiths and get a site visit booked in.

Authoritative guidance and manufacturer documents

For readers who want to check the rules and technical specifications directly, these are the sources behind the compliance and mechanical detail above:

Sources

FAQ

How much does it cost to install a maglock?

Costs vary with door type and wiring complexity, but standard lock installations in Ireland often run between €70 and €150, with more complex or high-security jobs reaching €300 or more. Maglock installations usually sit above this range because of the extra wiring, PSU and backup work involved, and fire alarm integration adds further labour.

How do I install a maglock door lock?

Mount the maglock to the frame header using the manufacturer’s specified hole pattern, then fit the armature plate to the door with a rubber and metal washer sandwich so it can rock and self-align against the magnet face. Wire in a correctly sized power supply, battery backup, REX device and door contacts, then commission and test the full system before handover.

Does a maglock need a power supply?

Yes, a maglock needs a continuous power supply to hold the door locked, since it draws power the entire time it is engaged rather than only during release. The power supply must be sized for the lock’s continuous voltage and current rating, and a battery backup is needed to maintain security during a mains outage.

What are the disadvantages of mag locks?

Maglocks are fail-safe, meaning they unlock automatically if power is lost, which some property owners see as a security drawback compared with fail-secure locks. They also require more wiring and peripheral hardware, PSU, battery backup, REX and often fire alarm integration, than a mechanical lock, and any fault in that power-cut path can leave the door either stuck locked or unable to hold securely.

What is a green box release used for?

A green box is a manual emergency release fitted beside a maglock on an escape route, wired to cut power to the lock directly and independently of the access control system. Official guidance lists it as a required feature for maglocks used on escape-route doors, alongside fire alarm integration.

maglock installationmagnetic door lock installationmaglock not releasingmaglock troubleshootingmaglock systemshow to install maglocksmagnetic door lock setupbest practices for maglock installationelectric lock installation
Back to Blog

What services do locksmiths in Ireland actually offer?

It’s more than just unlocking doors. Most locksmiths provide:

Emergency lockouts (home, car, business)

Lock repairs and replacements

Key cutting and rekeying

Security upgrades (e.g. anti-snap locks)

Car key replacement

How quickly can you respond to an emergency?

In emergency situations, typical arrival times should be at your location within 20-30 minutes. There are always professional locksmiths on standby, ready to handle any lockout or security emergency, ensuring safety is never compromised.

Can a lockmsith help with high-security locks and systems?

Absolutely! Most locksmiths specialise in advanced high-security lock systems, including electronic locks, biometric security, smart locks, and keyless entry systems. The should be trained in the latest security technologies, ensuring that they can provide the highest level of protection for your home, office, or vehicle. Ask for a free expert consultation to help you choose the right security system for your needs.

Will a locksmith provide a warranty on there services?

Yes, all locksmiths should stand by the quality of there work and offer a 100% satisfaction guarantee. Most would by default offer a warranty on all services, ensuring that you receive the best craftsmanship and long-lasting results.

Can a locksmith open Cars

Yes, most locksmiths are trained to open cars.

How quickly can a locksmith get to me in an emergency?

Most locksmiths in Ireland offer 24/7 emergency callouts and typically arrive within 15–60 minutes, depending on your location and traffic. In Dublin, response times can be as fast as 10–30 minutes, especially for emergency lockouts.

Can a locksmith open my door without damaging it?

Yes A professional locksmiths use non-destructive entry methods first. Drilling is usually a last resort, not the default approach.

If someone immediately suggests drilling without inspecting the lock, that’s a red flag.

How much does a locksmith cost?

Costs vary depending on the service, time of day, and complexity of the job. A standard lockout is usually cheaper than replacing a lock. Emergency or late-night services may cost more.

Prices vary, but here’s a realistic guide:

Standard callout/labour: €85–€95

Lockout service: from ~€85–€120+

Lock replacement: depends on parts + labour

Important: Always ask for a full quote upfront and if there is a call out fee. Some companies advertise low prices but increase costs after arriving.

Prices can vary quite a bit… call around for quotes!

Can you make a key without the original?

Yes A professional locksmiths use non-destructive methods whenever possible. Damage usually only happens if the lock is faulty, high-security, or has already been tampered with.

Do locksmiths in Ireland need to be licensed?

Yes. In Ireland, all locksmiths must be licensed by the Private Security Authority (PSA).

If you’re hiring someone:

Ask for their PSA licence number

Avoid anyone who can’t prove credentials

By asking for the licence you avoid the scammers.

Providing Locksmith Services For More Than 30 Years in Dublin, lock outs, lock fitting, slam locks, car opening, commerical and domestic.

Quick Links

Home

About Us

Services

Testimonial

Faqs

Contact Us

All Dublin Areas

Malahide

00353874377600

Legal

Privacy Policy

Terms & Conditions